B2B procurement · Specification review
A folded paper towel supplier should check double dispensing with the specified towel, its finished pack and the exact dispenser model. Run repeated pulls when the dispenser is full, half full and near empty. Record one-sheet, double-sheet, no-feed and torn-sheet outcomes separately, then approve a tested combination rather than assuming the fold name alone guarantees one-at-a-time release.
This is a dispenser-use trial, not a universal performance guarantee or a claim that Sansheng has measured a particular buyer's double-feed rate.
By Tracy Zhang · For facility-supply distributors and commercial washroom buyers · Prepared October 12, 2026
Send the current specification, identified sample and the decision you need to make.
Reusable procurement data

What should the buyer approve first?
A folded paper towel supplier should check double dispensing with the specified towel, its finished pack and the exact dispenser model. Run repeated pulls when the dispenser is full, half full and near empty. Record one-sheet, double-sheet, no-feed and torn-sheet outcomes separately, then approve a tested combination rather than assuming the fold name alone guarantees one-at-a-time release.
For folded paper towel supplier comparisons, approve the named sample and its actual use conditions before a bulk order.
Folded Paper Towel Supplier: Lock the towel and dispenser combination
Interfold, V-fold and Z-fold products may all fit a cabinet but behave differently at the opening. Specify the fold construction, sheet size, GSM, ply, embossing, pack count and finished stack height. Record the dispenser maker and model, slot dimensions, refill method and any internal pressure plate.
The folded paper towel supplier should send production-representative packs, not a loose handful of sheets. Packing compression can change how the first sheets separate. A fit-only check establishes loading clearance; it does not establish dispensing performance.

Count outcomes across refill stages
Define a pull protocol before seeing results: operator grip, direction, speed, number of pulls and when the pack is topped up. Count a double feed only when two or more sheets leave on one intended pull. Record a torn sheet or a no-feed separately because the corrective action may differ.
Check the first pulls after refill, the middle of the stack and the last usable sheets. The folded paper towel supplier should compare a retained approved pack and candidate under the same dispenser conditions. A single clean pull at a trade show is not enough evidence for a repeat order.

Look for the cause, not just the count
If double feeds cluster at a full dispenser, investigate overfilling or excessive stack compression. If they appear near empty, inspect interfold overlap and the path to the opening. Surface finish, embossing and sheet stiffness may also matter, but changing several variables at once makes the cause harder to identify.
Separate dispensing waste from a claimed cost-per-hand-dry saving. The trial can count extra sheets, while commercial savings also depend on actual consumption, price and site behavior. Do not infer a guaranteed reduction from one dispenser test.

Approve a usable purchasing specification
Keep the dispenser model, approved towel pack, trial method and observed outcomes with the RFQ. Ask what material or packing changes will trigger a repeat trial. If the distributor serves multiple dispenser fleets, maintain a compatibility matrix rather than blending all results into one average.
A folded paper towel supplier can quote an alternative format, but the buyer should rerun the same installed-use check before treating it as equivalent.
The buyer's comparison record
| Record level | Fields to confirm | Buyer purpose |
|---|---|---|
| Format | Fold, sheet dimensions and stack height | Keep samples comparable |
| Use stage | Full, middle, near empty and after refill | Expose stage-specific double feeds |
| Result | Single, double, no-feed and torn counts | Choose the right corrective action |
What belongs in the RFQ?
Ask the folded paper towel supplier to respond against one identified product and a written acceptance decision.
- List dispenser maker/model and slot or pressure-plate details.
- Specify fold, sheet size, GSM, ply, pack count and stack height.
- Agree pull count, refill stages and outcome categories before testing.
- Keep an identified approved pack and define a change-control trigger.
For adjacent decisions, read the related Sansheng purchasing guide and the companion specification check. Keep each approval question separate.
Questions buyers also ask
If the stack fits, will it dispense one sheet at a time?
Not necessarily. Fit and separation are different decisions; run a repeated pull trial.
Should a double feed be counted as a torn sheet?
No. Track double, torn and no-feed outcomes separately so the cause can be investigated.
Can one dispenser model approve a whole customer network?
Only if the installed dispenser fleet is the same and the buyer accepts that evidence scope.
Sources and scope notes
- Sansheng paper towels product program Supports: Identifies folded towel formats and specification choices. Limit: Does not document a passed double-feed trial in a named dispenser.
Sources checked October 12, 2026. Images are illustrative and do not document a Sansheng test, customer order or shipment.
Request a same-spec review
Send the dispenser model, towel fold, pack specification and a short clip or count sheet from the current problem. Sansheng can discuss a comparable sample and the trial conditions before a volume decision.

Sales Manager at Sansheng Paper · 20+ years in tissue paper OEM & bulk export · LinkedIn





