B2B procurement · Buyer guide
Verify unfolded sheet dimensions by opening finished mini packs from identified lots, carefully unfolding sheets without stretching, and measuring width and length under a recorded room condition. Record the fold pattern and variation across packs separately from the external pack size. A compact pack can hide an undersized or unevenly folded sheet.
This is a buyer-defined dimensional inspection, not a claim about an identified Sansheng lot or a universal pocket-tissue size standard.
Send the exact SKU, buying destination and inspection question you need reviewed.
Reusable procurement data

Direct answer
Verify unfolded sheet dimensions by opening finished mini packs from identified lots, carefully unfolding sheets without stretching, and measuring width and length under a recorded room condition. Record the fold pattern and variation across packs separately from the external pack size. A compact pack can hide an undersized or unevenly folded sheet.
Lock the sheet drawing and pack revision
Ask the pocket tissue supplier for the unfolded sheet target, ply count, fold drawing, sheets per pack and packaging artwork revision. Note whether the target is before or after folding and whether dimensions include any trimmed edge. Use finished saleable packs, not loose sheets supplied separately. Select packs from multiple cartons and positions in the converting run. This makes it possible to tie an undersized sheet to a batch rather than a single opened sample.

Open and unfold without changing the sheet
Photograph the sealed pack and the first sheet position before handling. Remove sheets without pulling across a sticky flap or tearing at the opening. Unfold on a flat, clean surface and let the sheet rest; do not stretch corners to reach the nominal measurement. Record the room condition and time out of pack. ISO 187:2022 describes conditioning atmospheres for paper and board, but it does not prescribe an OEM pocket-tissue dimension or acceptance limit.

Measure both axes and the fold
Use one ruler or calibrated image method for the long and short directions and record individual values, not only an average. Note skew, uneven cut edges, fold offset and ply separation. Compare at least the top, middle and lower sheets in each sampled pack. If the external mini pack looks correct but unfolded sheets differ, investigate cut width, folding registration and packing compression separately. The pocket tissue supplier should keep the original pack with its sheet measurements.

Write an approval rule for repeat orders
Agree width and length tolerances, the handling method and a defect rule for torn or misfolded sheets. Keep an approved unfolded sheet and fold drawing alongside the printed mini pack. Reapprove after changes to cut tooling, fold plates, ply bonding, pack film or pack count. Do not infer sheet area from the packet dimensions. A pocket tissue supplier should report the actual sheet distribution from the sampled lot before the buyer signs off the OEM artwork claim.
Buyer comparison record
| Check | Record | Buyer purpose |
|---|---|---|
| Identity | SKU, pack revision and lot | Trace each sheet |
| Preparation | Opening and room condition | Avoid stretching bias |
| Dimensions | Individual width and length | Find variation |
| Fold | Offset, skew and damage | Check usable format |
What should buyers ask the pocket tissue supplier?
- Unfolded sheet drawing and fold pattern
- Finished mini packs sampled across cartons and run positions
- Individual long- and short-axis readings with pack IDs
- Approved dimensional tolerances and change triggers
Send the pocket tissue supplier your intended use, destination and required acceptance decision.
Private Label Pocket Tissue: Which Pack Tests Prevent Seal and Count Complaints?
Pocket Tissue Supplier: How to Check Tear-Open Force Across OEM Packs?
Pocket Tissue Supplier: How to Match Lot Codes Across Mini Packs and Cartons?
Questions buyers also ask
Can the outside pack size establish sheet size?
No. Fold pattern and compression change the relationship.
Should sheets be pulled taut for measurement?
No. Use a repeatable flat handling method without stretching.
Does ISO 187 set a pocket-tissue size limit?
No. It addresses conditioning and testing atmosphere, not the buyer dimension.
Sources and scope notes
- ISO 187:2022 Supports: Specifies standard atmospheres and conditioning procedures for paper testing. Limit: Does not set a pocket-tissue sheet size or pass tolerance.
- Sansheng pocket tissue product page Supports: Identifies the mini-pack product context. Limit: Does not provide measurements for the sampled OEM lot.
Source scope checked October 26, 2026. Illustrative images do not document a Sansheng test, certified SKU or customer order.
Request an identified sample review
Send the pocket tissue supplier your exact SKU, approved sample, buying destination and evidence requirement. The record can then be matched to the decision before a quote or release.

Sales Manager at Sansheng Paper · 20+ years in tissue paper OEM & bulk export · LinkedIn





