Blog

Sansheng Paper--Your Nearby Supplier of Household Tissue Paper

TAD Paper Supplier: How to Check Web Edge Fraying?

Table of Contents

B2B procurement · Buyer guide

A TAD paper supplier should identify the roll and map loose fibers or ragged cuts along the exposed web edge, then run a controlled converting trial on the affected section. Record edge location, length and the finished-sheet consequence. A crushed roll end is a transport geometry issue; fraying is an edge condition of the web itself and requires a separate decision.

This is an inspection and converting-trial method. It does not establish a Sansheng edge-fray rate, lint value or universal reject length.

By Tracy Zhang · For tissue converters buying TAD parent rolls · Prepared

Send the exact SKU, buying destination and inspection question you need reviewed.

Request a Same-Spec Review WhatsApp +86 157 6268 3071

Reusable procurement data

TAD tissue supplier textured tissue roll and sheet beside a caliper on a sample table
Illustrative image: TAD roll and exposed edge for identification. Existing site media shows product context, not a test or identified lot result.

Direct answer

A TAD paper supplier should identify the roll and map loose fibers or ragged cuts along the exposed web edge, then run a controlled converting trial on the affected section. Record edge location, length and the finished-sheet consequence. A crushed roll end is a transport geometry issue; fraying is an edge condition of the web itself and requires a separate decision.

Identify the affected web edge

Photograph the wrapped roll before opening, then mark left or right web edge relative to unwind direction. Record whether fibers are loose only on outer turns or recur deeper in the roll. Keep the roll ID, slit width and approximate distance from the roll start. A ragged edge near one splice is different from a continuous cut-quality issue. Protect the sample from handling lint during inspection.

Textured tissue roll beside two embossed white sheet specimens
Illustrative image: Web edge and clean comparison strip. Existing site media shows product context, not a test or identified lot result.

Describe the defect consistently

Agree whether the report records visible protruding fibers, detached fiber clusters, width loss or web breaks. Measure the affected length and cross-web location where possible, and retain both an affected and a clean reference strip from the same roll. Do not convert one photograph into a numerical reject rate. ISO tissue vocabulary gives common terms, but it does not prescribe this buyer’s edge-fray tolerance.

Two tissue rolls and three sheets with different surface patterns
Illustrative image: Converter feed path for trial context. Existing site media shows product context, not a test or identified lot result.

Trial the converting path

Feed the identified section through the intended rewinder, embossing or towel line at a documented speed. Record trim loss, edge breaks, dust accumulation and whether the defect appears on the finished sheet or pack. Compare the result with a clean section under the same settings. Fraying that disappears in planned trim has a different commercial effect from fibers that enter the saleable sheet; record the distinction.

Source for this method: ISO 12625-1:2019 tissue vocabulary. It does not set a core, width, edge or dispenser acceptance limit for a Sansheng SKU.

Large tissue parent roll supported in an industrial cradle
Illustrative image: Retained roll label and finished sheet samples. Existing site media shows product context, not a test or identified lot result.

Set a bounded disposition

Specify how much affected web may be trimmed, held for trial or rejected under the buyer’s plan. The supplier and converter should agree who measures the affected length and how credit or replacement is calculated if required. Keep roll labels, photos, samples and finished output together. Recheck the edge after slit-width, blade or winding changes; a previous roll acceptance does not automatically cover a changed process.

Buyer comparison record

CheckRecordBuyer purpose
LocationLeft/right edge and roll depthScopes exposure
AppearanceFibers, ragged cut or width lossSeparates mechanisms
TrialTrim, breaks and finished sheetsShows converting consequence
DispositionAffected length and remedyAvoids blanket conclusions

What should buyers ask the tad paper supplier?

  • Roll ID, unwind direction and edge map
  • Agreed visual definition and sampling length
  • Converter line, speed and trim width
  • Disposition and retained-sample rule

Send the tad paper supplier your intended use, destination and required acceptance decision.

TAD Paper Supplier: Does Rewinding Reduce Caliper?

TAD Paper Supplier: How to Approve Embossing Trials?

TAD Paper Supplier: How to Resolve Conflicting Lab Results?

Questions buyers also ask

Is edge fraying the same as end-face crush?

No. Check the tissue web edge separately from roll-end geometry.

Can a photo approve the roll?

No. Map the defect and trial the affected web where converting performance matters.

Does ISO set a reject length?

No. The buyer and supplier must agree an acceptance rule.

Sources and scope notes

  1. ISO 12625-1:2019 tissue vocabulary Supports: Defines shared terminology for tissue paper and tissue products. Limit: It does not set a core, width, edge or dispenser acceptance limit for a Sansheng SKU.
  2. Sansheng tad product page Supports: Identifies the relevant Sansheng product family and supply context. Limit: It does not document a tested lot, approved tolerance or a production result.

Source scope checked November 16, 2026. Illustrative images do not document a Sansheng test, certified SKU or customer order.

Request an identified sample review

Send the tad paper supplier your exact SKU, approved sample, destination and evidence requirement. Match the available record to your buying decision before a quote or release.

Send Your Specification WhatsApp +86 157 6268 3071

Tracy Zhang
Tracy Zhang

Sales Manager at Sansheng Paper · 20+ years in tissue paper OEM & bulk export · LinkedIn

Facebook
Twitter
Email
Print

We will contact you within 1 working day, please pay attention to the email with the suffix “sspaperpack.com”

We will contact you within 1 working day, please pay attention to the email with the suffix “sspaperpack.com”.

Get Confirmed MOQ, FOB Price, Lead Time and Loading Estimate
tissue paper manufacturer