B2B procurement · Buyer guide
An airlaid napkin supplier should measure finished pack height with the specified sheet count, fold format, sleeve and a repeatable compression or no-load method. Compare identified packs from the run with the buyer’s carton and dispenser allowance. A loose napkin caliper reading does not predict the thickness of a packed stack, and pack height by itself does not measure fold recovery.
This guide sets a buyer-defined dimension check, not a Sansheng batch result or a universal hotel napkin pack limit.
Send the exact SKU, buying destination and inspection question you need reviewed.
Reusable procurement data

Direct answer
An airlaid napkin supplier should measure finished pack height with the specified sheet count, fold format, sleeve and a repeatable compression or no-load method. Compare identified packs from the run with the buyer’s carton and dispenser allowance. A loose napkin caliper reading does not predict the thickness of a packed stack, and pack height by itself does not measure fold recovery.
Fix what counts as one pack
State sheet count, open and folded dimensions, ply or material construction, sleeve type and whether the pack is measured before or after case compression. Record whether the carton contains individually wrapped stacks or loose bundles. Without a fixed configuration, suppliers may quote different pack heights for the same nominal napkin. Retain one fully packed reference with its artwork and lot identification.

Use one height measurement method
Specify a flat support, the contact plate or measuring device, any applied load, dwell time and conditioning. Measure at defined points rather than pressing the tallest corner by hand. Record individual packs from the start, middle and end of production, and keep the result with pack count. ISO tissue thickness guidance concerns specimen measurement under defined pressure; it does not supply a finished airlaid pack-height limit.
Source for this method: EDANA Nonwovens Standard Procedures catalogue. It does not define a folded airlaid-napkin pack-height tolerance.

Check the carton and dispensing consequence
Place packs at the target case count and verify closure, case bulge and pallet stacking clearance. For foodservice use, confirm that a pack can be removed and opened without crushing its folded edges. A low pack height may reflect undercounting, a different fold or excessive compression; a high pack may point to trapped air or changing folds. Investigate the cause before adjusting the carton size.

Write a repeatable acceptance window
Use the signed pack sample and actual customer shelf or dispenser space to set minimum and maximum height. State the sample plan and what happens when a pack misses the range. Keep fold recovery, emboss and sheet separation as separate tests. On repeat orders, compare the first article with the approved pack and record any change in sleeve, fold or sheet count before releasing production.
Buyer comparison record
| Check | Record | Buyer purpose |
|---|---|---|
| Configuration | Count, fold and sleeve | Makes packs comparable |
| Method | Plate, load and dwell | Controls measurement |
| Fit | Case and dispensing check | Shows buyer consequence |
| Release | Height window and plan | Controls repeat orders |
What should buyers ask the airlaid napkin supplier?
- Approved napkin fold and pack-count drawing
- Height method, conditioning and acceptance window
- Case count, carton dimensions and target dispenser
- First-article and repeat-lot sample plan
Send the airlaid napkin supplier your intended use, destination and required acceptance decision.
Airlaid Napkin Manufacturer: Does the Fold Recover After Packing?
Airlaid Napkin Supplier: How to Check Cut-Edge Fraying After Folding?
Airlaid Napkin Supplier: How to Check Logo Placement After Folding?
Questions buyers also ask
Can loose-sheet caliper set pack height?
No. Measure the finished counted and sleeved stack.
Does pack height prove fold recovery?
No. Test fold recovery separately under its own method.
Should the limit be universal?
No. Set it from the buyer’s carton and use requirements.
Sources and scope notes
- EDANA Nonwovens Standard Procedures catalogue Supports: Identifies harmonized nonwoven sampling and test procedures. Limit: It does not define a folded airlaid-napkin pack-height tolerance.
- Sansheng airlaid napkin product page Supports: Identifies the relevant Sansheng product family and supply context. Limit: It does not document a tested lot, approved tolerance or a production result.
Source scope checked November 16, 2026. Illustrative images do not document a Sansheng test, certified SKU or customer order.
Request an identified sample review
Send the airlaid napkin supplier your exact SKU, approved sample, destination and evidence requirement. Match the available record to your buying decision before a quote or release.

Sales Manager at Sansheng Paper · 20+ years in tissue paper OEM & bulk export · LinkedIn





